Preparation of Titanium Dioxide (TiO2) from Waste of Polymetallic Ore Processing via Sulfurization Treatment

https://doi.org/10.22146/ijc.89992

Enkh-Uyanga Otgon-Uul(1), Munkhtsetseg Baatar(2*), Ulziijargal Nanzad(3), Jargalsaikhan Lkhamsuren(4)

(1) Department of Chemistry, School of Arts & Sciences, National University of Mongolia, Ikh surguuliin gudamj 1, Baga toiruu, Ulaanbaatar 14201, Mongolia
(2) Department of Innovation and Technology, Ulaanbaatar Science and Technology Park, National University of Mongolia, Bayanzurkh District, Box 167, Ulaanbaatar 210651, Mongolia
(3) Department of Innovation and Technology, Ulaanbaatar Science and Technology Park, National University of Mongolia, Bayanzurkh District, Box 167, Ulaanbaatar 210651, Mongolia
(4) Institute of Chemistry and Chemical Technology, Mongolian Academy of Sciences Peace Avenue, 4th Building of the MAS, Ulaanbaatar 13330, Mongolia
(*) Corresponding Author

Abstract


Various experimental conditions were applied to extract titanium oxide from the waste of polymetallic ore. X-ray diffraction (XRD) analysis confirms that the waste of polymetallic ore contains including various minerals such as almandine (Fe,Mg,Ca)3Al2Si3O12, brownmillerite (FeAlO3(CaO)2), quartz (SiO2), magnetite (Fe3O4). Using H2SO4 acid with a concentration of 93% in the S/L mass ratio of 1:1.5 at 140 °C is suggested as an optimum reaction condition. Its hydrolysis subsequently leads to the formation of the titanyl sulfate (TiOSO4), and relatively pure titanium oxide is obtained through precipitation and calcination at 600 °C. The observed band gap value of 3.2 eV for the obtained TiO2 corresponds to the typical band gap value of anatase-type TiO2. We calculated the crystallite size of extracted anatase-type titanium oxide according to the Debye-Scherrer equation it was determined to be 96.35 nm. Fully reflecting X-ray fluorescence (XRF) determined that the purity of extracted TiO2 is 93.18%. This report presents a newly developed process that enables the production of relatively high-purity TiO2 (93.18%) from the waste of polymetallic ore (TiO2 5.39%) by a simple sulfurization process.

Keywords


anatase-titanium dioxide; minerals leaching; low-grade ore; X-ray diffraction (XRD) analysis; secondary resource

Full Text:

Full Text PDF


References

[1] Feng, E., Gao, D., Wang, Y., Yu, F., Wang, C., Wen, J., Gao, Y., Huang, G., and Xu, S., 2023, Sustainable recovery of titanium from secondary resources: A review, J. Environ. Manage., 339, 117818.

[2] Anucha, C.B., Altin, I., Bacaksiz, E., and Stathopoulos, V.N., 2022, Titanium dioxide (TiO₂)-based photocatalyst materials activity enhancement for contaminants of emerging concern (CECs) degradation: In the light of modification strategies, Chem. Eng. J. Adv., 10, 100262.

[3] Froes, F.H., 2015, Titanium: Physical Metallurgy, Processing, and Applications, ASM International, Materials Park, Ohio, pp.354–374.

[4] Haider, A.J., Jameel, Z.N., and Al-Hussaini, I.H.M., 2019, Review on: Titanium dioxide applications, Energy Procedia, 157, 17–29.

[5] El Khalloufi, M., Drevelle, O., and Soucy, G., 2021, Titanium: An overview of resources and production methods, Minerals, 11 (12), 1425.

[6] Mamaghani, A.H., Haghighat, F., and Lee, C.S., 2020, Role of titanium dioxide (TiO2) structural design/morphology in photocatalytic air purification, Appl. Catal., B, 269, 118735.

[7] Sampath, A.H.J., Wickramasinghe, N.D., de Silva, K.M.N., and de Silva, R.M., 2023, Methods of extracting TiO2 and other related compounds from ilmenite, Minerals, 13(5), 662.

[8] Haverkamp, R.G., Kruger, D., and Rajashekar, R., 2016, The digestion of New Zealand ilmenite by hydrochloric acid, Hydrometallurgy, 163, 198–203.

[9] Subramanyam, R.B., 1993, Some recent innovations in the Kroll process of titanium sponge production, Bull. Mater. Sci., 16 (6), 433–451.

[10] Morsella, M., d’Alessandro, N., Lanterna, A.E., and Scaiano, J.C., 2016, Improving the sunscreen properties of TiO2 through an understanding of its catalytic properties, ACS Omega, 1 (3), 464–469.

[11] Miyoshi, A., Nishioka, S., and Maeda, K., 2018, Water splitting on rutile TiO2-based photocatalysts, Chem. - Eur. J., 24 (69), 18204–18219.

[12] Cowan, A.J., Leng, W., Barnes, P.R.F., Klug, D.R., and Durrant, J.R., 2013, Charge carrier separation in nanostructured TiO2 photoelectrodes for water splitting, Phys. Chem. Chem. Phys., 15 (22), 8772–8778.

[13] Zhang, X., Tan, X., Li, C., Yi, Y., and Liu, W., 2019, Energy-efficient and simultaneous extraction of lithium, rubidium and cesium from lepidolite concentrate via sulfuric acid baking and water leaching, Hydrometallurgy, 185, 244–249.

[14] Hisatomi, T., Kubota, J., and Domen, K., 2014, Recent advances in semiconductors for photocatalytic and photoelectrochemical water splitting, Chem. Soc. Rev., 43 (22), 7520–7535.

[15] Kubacka, A., Diez, M.S., Rojo, D., Bargiela, R., Ciordia, S., Zapico, I., Albar, J.P., Barbas, C., Martins dos Santos, V.A.P., Fernández-García, M., and Ferrer, M., 2014, Understanding the antimicrobial mechanism of TiO2-based nanocomposite films in a pathogenic bacterium, Sci. Rep., 4 (1), 4134.

[16] Eddy, D.R., Ishmah, S.N., Permana, M.D., and Firdaus, M.L., 2020, Synthesis of titanium dioxide/silicon dioxide from beach sand as photocatalyst for Cr and Pb remediation, Catalysts, 10 (11), 1248.

[17] Shi, J., Qiu, Y., Yu, B., Xie, X., Dong, J., Hou, C., Li, J., and Liu, C., 2022, Titanium extraction from titania-bearing blast furnace slag: A review, JOM, 74 (2), 654–667.

[18] Zhang, W., Zhang, L., Li, Y., and Li, X., 2015, An environmental procedure to extract titanium components and metallic iron from Ti-bearing blast furnace slag, Green Process. Synth., 4 (4), 307–316.

[19] Frias, C., Palma, J., Garcia, M.A., and Diaz, G., 2002, “Recovery of Precious Metals from Metallurgical Residues by Applying the PLINT” in Chloride Metallurgy 2002: Practice and Theory of Chloride/Metal Interaction, Canadian Institute of Mining, Metallurgy and Petroleum, Montreal, Canada, 29–40.

[20] Sulistiyono, E., Handayani, M., Prasetyo, A.B., Irawan, J., Febriana, E., Firdiyono, F., Yustanti, E., Sembiring, S.N., Nugroho, F., and Muslih, E.Y., 2021, Implementation of sulfuric acid leaching for aluminum and iron removal for improvement of low-grade silica from quartz sand of Sukabumi, Indonesia, East.-Eur. J. Enterp. Technol., 3, 32–40.

[21] Wang, M., Woo, K.D., Kim, I.Y., Woong-Ki, and Sui, Z., 2007, Separation of Fe3+ during hydrolysis of TiO2+ by addition of EDTA, Hydrometallurgy, 89 (3-4), 319–322.

[22] Li, P., Luo, S.H., Feng, J., Lv, F., Yan, S., Wang, Q., Zhang, Y., Mu, W., Liu, X., Lei, X., Teng, F., Li, X., Chang, L., Liang, J., and Duan, X., 2021, Study on the high-efficiency separation of Fe in extracted vanadium residue by sulfuric acid roasting and the solidification behavior of V and Cr, Sep. Purif. Technol., 269, 118687.

[23] Baatar, M., Otgon-Uul, E.U., Urtnasan, U., Nanzad, U., Ayush, E., and Gelegbadam, A., 2017, Research on utilization of anatase (TiO2) extracted from polymetallic ore for waste water treatment process, Int. Proc. Chem., Biol. Environ. Eng., 100, 47–53.



DOI: https://doi.org/10.22146/ijc.89992

Article Metrics

Abstract views : 2916 | views : 999


Copyright (c) 2024 Indonesian Journal of Chemistry

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

 

Indonesian Journal of Chemistry (ISSN 1411-9420 /e-ISSN 2460-1578) - Chemistry Department, Universitas Gadjah Mada, Indonesia.

Web Analytics View The Statistics of Indones. J. Chem.