Electrical Discharge Machining (EDM) untuk Manufaktur Presisi Orifice Nozzle Injector Mesin Diesel: Sistematik Review Kemajuan, Optimalisasi, Dan Keberlanjutan
Kata Kunci:
Electrical Discharge Machining, Optimalisasi, Proses Hibrida, Modifikasi Permukaan, Manufaktur BerkelanjutanAbstrak
Electrical Discharge Machining (EDM) telah berkembang pesat dari proses pemesinan non-konvensional menjadi teknologi manufaktur presisi tinggi yang krusial untuk material canggih. Ulasan ini menyajikan tinjauan sistematis terhadap perkembangan terkini dalam teknologi EDM berdasarkan analisis artikel penelitian yang diterbitkan antara tahun 2019 hingga 2025. Fokus utama ulasan ini mencakup empat area utama: (1) optimalisasi parameter proses menggunakan metodologi cerdas seperti swarm intelligence, machine learning, dan Response Surface Methodology (RSM); (2) inovasi proses hibrida, termasuk Powder-Mixed EDM (PMEDM), EDM berbantuan ultrasonik dan medan magnet, serta penggunaan dielektrik-elektrolitik untuk menghasilkan permukaan bebas cacat; (3) pengembangan material elektroda dan pemesinan paduan canggih seperti paduan titanium, Shape Memory Alloys (SMA), dan paduan magnesium; serta (4) tren keberlanjutan dalam EDM melalui penggunaan dielektrik ramah lingkungan dan minimalisasi dampak lingkungan. Hasil sintesis menunjukkan bahwa arah penelitian EDM bergerak menuju proses yang lebih cerdas, efisien, multifungsi (melalui modifikasi permukaan), dan berkelanjutan. Ulasan ini menyimpulkan dengan menyoroti tantangan yang ada dan memberikan saran untuk arah penelitian di masa depan.
Referensi
J. B. Heywood, Internal Combustion Engine Fundamentals. McGraw-Hill Publishing Company, 2018.
J. Xia, Q. Zhang, Z. Huang, D. Ju, and X. Lu, “Experimental study of injection characteristics under diesel’s sub/trans/supercritical conditions with various nozzle diameters and injection pressures,” Energy Convers. Manag., vol. 215, no. May, p. 112949, 2020, doi: 10.1016/j.enconman.2020.112949.
M. Vijay Kumar, A. Veeresh babu, P. Ravi Kumar, and T. Manoj Kumar Dundi, “Influence of different nozzle hole orifice diameter on performance, combustion and emissions in a diesel engine,” Aust. J. Mech. Eng., vol. 18, no. 2, pp. 179–184, 2020, doi: 10.1080/14484846.2018.1453975.
R. Balz, B. von Rotz, and D. Sedarsky, “In-nozzle flow and spray characteristics of large two-stroke marine diesel fuel injectors,” Appl. Therm. Eng., vol. 180, p. 115809, 2020, doi: 10.1016/j.applthermaleng.2020.115809.
O. Klyus, M. Szczepanek, G. Kidacki, P. Krause, S. Olszowski, and L. Chybowski, “The Effect of Internal Combustion Engine Nozzle Needle Profile on Fuel Atomization Quality,” Energies, vol. 17, no. 1, 2024, doi: 10.3390/en17010266.
M. S. Rasheed, “Comparison of Micro-Holes Produced By Micro-EDM with Laser Machining,” Int. J. Sci. Mod. Eng., vol. 1, no. 3, pp. 14–18, 2013.
X. Mao, S. Almeida, J. Mo, and S. Ding, “The state of the art of electrical discharge drilling: a review,” Int. J. Adv. Manuf. Technol., vol. 121, no. 5–6, pp. 2947–2969, 2022, doi: 10.1007/s00170-022-09549-7.
D. T. Pham, S. S. Dimov, S. Bigot, A. Ivanov, and K. Popov, “Micro-EDM - Recent developments and research issues,” J. Mater. Process. Technol., vol. 149, no. 1–3, pp. 50–57, 2004, doi: 10.1016/j.jmatprotec.2004.02.008.
L. Li, C. Diver, J. Atkinson, R. Giedl-Wagner, and H. J. Helml, “Sequential laser and EDM micro-drilling for next generation fuel injection nozzle manufacture,” CIRP Ann. - Manuf. Technol., vol. 55, no. 1, pp. 179–182, 2006, doi: 10.1016/S0007-8506(07)60393-X.
F. K. Thomas Bergs, Manufacturing Processes 3: Electrical Discharge Machining, Electrochemical Manufacturing and Beam Processes. Springer Berlin, Heidelberg, 2025. [Online]. Available: https://doi.org/10.1007/978-3-662-70580-3
M. H. A. and A. E. Jaber E. Abu Qudeiri , Aiman Zaiout, Abdel-Hamid I. Mourad, “Principles and Characteristics of Different EDM Processes in Machining Tool and Die Steels,” Appl. Sci., vol. Appl. Sci., pp. 1–46, 2020, [Online]. Available: doi:10.3390/app10062082
A. Bin Rashid, T. Saba, S. Das Sourav, M. T. Ilhum, M. K. Bappy, and A. Tomal, “Investigation of the effect of micromachining parameters on the accuracy of micro-holes drilled by electric discharge machine,” Results in Surfaces and Interfaces, vol. 20, no. March, p. 100603, 2025, doi: 10.1016/j.rsurfi.2025.100603.
Y. Chen, S. Hu, A. Li, Y. Cao, Y. Zhao, and W. Ming, “Parameters Optimization of Electrical Discharge Machining Process Using Swarm Intelligence: A Review,” Metals (Basel)., vol. 13, no. 5, 2023, doi: 10.3390/met13050839.
M. Sana, M. Asad, M. U. Farooq, S. Anwar, and M. Talha, “Machine learning for multi-dimensional performance optimization and predictive modelling of nanopowder-mixed electric discharge machining (EDM),” Int. J. Adv. Manuf. Technol., vol. 130, no. 11–12, pp. 5641–5664, 2024, doi: 10.1007/s00170-024-13023-x.
Jagadish, D. Zindani, A. Selvam, G. G. Tejani, and A. J. Santhosh, “Optimization of process parameter for green die sinking electrical discharge machining: a novel hybrid decision-making approach,” Sci. Rep., vol. 15, no. 1, pp. 1–19, 2025, doi: 10.1038/s41598-025-92713-2.
M. S. Sisodiya and P. Agarwal, “Short review on the development of electrical discharge machine,” Eng. Res. Express, vol. 6, no. 1, 2024, doi: 10.1088/2631-8695/ad2be3.
M. S. Tufail, J. Giri, E. Makki, T. Sathish, R. Chadge, and N. Sunheriya, “Machinability of different cutting tool materials for electric discharge machining: A review and future prospects,” AIP Adv., vol. 14, no. 4, 2024, doi: 10.1063/5.0201614.
C. Sarala Rubi et al., “Comprehensive review on wire electrical discharge machining: a non-traditional material removal process,” Front. Mech. Eng., vol. 10, no. January, pp. 1–16, 2024, doi: 10.3389/fmech.2024.1322605.
G. Li, W. Natsu, and Z. Yu, “Study on Debris Behavior and Its Influence on EDM Characteristics in Deep Micro-hole Machining,” Procedia CIRP, vol. 68, no. April, pp. 578–581, 2018, doi: 10.1016/j.procir.2017.12.117.
M. Machno, A. Matras, and M. Szkoda, “Modelling and Analysis of the Effect of EDM-Drilling Parameters on the Machining Performance of Inconel 718 Using the RSM and ANNs Methods,” Materials (Basel)., vol. 15, no. 3, 2022, doi: 10.3390/ma15031152.
D. Popa and C.-O. Morariu, “Modern Technologies for Micro-drilling of the Fuel Injector Nozzle used in Motor Vehicles - A Review of the Literature,” MATEC Web Conf., vol. 343, p. 03007, 2021, doi: 10.1051/matecconf/202134303007.
S. Kalpakjian and S. R. Schmid, Manufacturing engineering and technology, vol. 25, no. 1. 2013. doi: 10.1016/0924-0136(91)90107-p.
S. Ahmed, A. Speidel, J. W. Murray, N. Ahmed, M. Cuttell, and A. T. Clare, “Electrolytic-dielectrics: A route to zero recast electrical discharge machining,” Int. J. Mach. Tools Manuf., vol. 181, no. September, p. 103941, 2022, doi: 10.1016/j.ijmachtools.2022.103941.
M. K. Dikshit et al., “Surface characteristics optimization of biocompatible Ti6Al4V with RCCD and NSGA II using die sinking EDM,” J. Mater. Res. Technol., vol. 24, pp. 223–235, 2023, doi: 10.1016/j.jmrt.2023.03.005.
R. Balz, G. Bernardasci, B. von Rotz, and D. Sedarsky, “Influence of nozzle geometry on spray and combustion characteristics related to large two-stroke engine fuel injection systems,” Fuel, vol. 294, p. 120455, 2021, doi: 10.1016/j.fuel.2021.120455.
R. Payri, F. J. Salvador, J. Gimeno, and L. D. Zapata, “Diesel nozzle geometry influence on spray liquid-phase fuel penetration in evaporative conditions,” Fuel, vol. 87, no. 7, pp. 1165–1176, 2008, doi: 10.1016/j.fuel.2007.05.058.
V. C. Pham, V. V. Le, S. Yeo, J. H. Choi, and W. J. Lee, “Effects of the Injector Spray Angle on Combustion and Emissions of a 4-Stroke Natural Gas-Diesel DF Marine Engine,” Appl. Sci., vol. 12, no. 23, 2022, doi: 10.3390/app122311886.
J. Yan, S. Gao, W. Zhao, and T. H. Lee, “Study of combustion and emission characteristics of a diesel engine fueled with diesel, butanol-diesel and hexanol-diesel mixtures under low intake pressure conditions,” Energy Convers. Manag., vol. 243, p. 114273, 2021, doi: 10.1016/j.enconman.2021.114273.
D. N. M. Kumar and M. P. C. Rao, “Optimization of EDM Process Parameters using Response Surface Methodology for AISI D3 Steel,” Int. J. Trend Sci. Res. Dev., vol. Volume-3, no. Issue-3, pp. 1651–1656, 2019, doi: 10.31142/ijtsrd23535.
V. Mohankumar et al., “Optimizing EDM process parameters with the use of GRA-based RSM for machining titanium alloy,” Results Eng., vol. 26, no. March, p. 104903, 2025, doi: 10.1016/j.rineng.2025.104903.
R. Das and M. K. Pradhan, “ANN modelling for surface roughness in electrical discharge machining: a comparative study,” Int. J. Serv. Comput. Oriented Manuf., vol. 1, no. 2, p. 124, 2013, doi: 10.1504/ijscom.2013.058674.
K. Deb, A. Pratap, S. Agarwal, and T. Meyarivan, “A fast and elitist multiobjective genetic algorithm: NSGA-II,” IEEE Trans. Evol. Comput., vol. 6, no. 2, pp. 182–197, 2002, doi: 10.1109/4235.996017.
A. Y. Fatatit and A. Kalyon, “The Environmental Impact of Electric Discharge Machining,” Int. J. Eng. Sci. Appl., vol. 3, no. 3, pp. 123–129, 2019.
W. Ming et al., “Research on EDM Performance of Renewable Dielectrics under Different Electrodes for Machining SKD11,” Crystals, vol. 12, no. 2, 2022, doi: 10.3390/cryst12020291.
A. A. Abbas, R. R. Shwaish, S. H. Aghdeab, and W. Ahmed, “Energy efficiency and sustainability enhancement of electric discharge machines by incorporating nano-graphite,” Mater. Res. Proc., vol. 43, pp. 124–131, 2024, doi: 10.21741/9781644903216-17.
D. Song et al., “Highly energy-efficient and safe-environment-friendly ultra short electrical arc machining for titanium alloy: Mechanism, characteristics, and parameter estimation,” J. Clean. Prod., vol. 417, no. March, p. 137842, 2023, doi: 10.1016/j.jclepro.2023.137842.












