Bandwidth Upgrade in Printed Dipole Antennas Design for LTE Base Station

https://doi.org/10.22146/ijitee.43842

Rahardian Luthfi Prasetyo(1), Iswandi Iswandi(2*), Eny Sukani Rahayu(3)

(1) Universitas Gadjah Mada
(2) Universitas Gadjah Mada
(3) Universitas Gadjah Mada
(*) Corresponding Author

Abstract


Abstract—In this study the research design development has been carried out by changing the radiating element field width. Radiating element field extension was administered by simulating it and trying to measure the value one by one in antenna simulator software.  The radiating element widening was administered so that the resulting bandwidth could be greater. After changing the width of the field, an element radiating field length adjustment was administered to adjust the operating frequency used in Indonesia. After the design worked at the desired frequency and produced a desired bandwidth, antenna fabrication was administered and its results was tested using Mini VNA Tiny to find out the antenna value if mass produced.


Keywords


LTE;antenna;femtocell;printed dipole;triple-band

Full Text:

PDF


References

The Ministry of Communication and Information of the Republic of Indonesia, "Peraturan Menteri Komunikasi dan Informatika Republik Indonesia Nomor 27 Tahun 2015 tentang Persyaratan Teknis Alat dan/atau Perangkat-Perangkat Telekomunikasi Bebasis Standar Teknologi Long Term Evolution," Jakarta, July, 2015.

A.K.D. Jaya, "Perancangan Triple-band Printed Dipole Antenna untuk Femtocell dalam Ruangan pada Sistem Komunikasi LTE," Thesis, Universitas Gadjah Mada, Yogyakarta, Indonesia, 2017.

M.N.Z. Akbar, "Perancangan Dual-band Printed Ceiling Antenna untuk Jaringan LTE pada Frekuensi 1800/2300 MHz," Thesis, Gadjah Mada University, Yogyakarta, Indonesia, 2017.

Iswandi, A.K.D. Jaya, and E.S. Rahayu, “Design of Triple Band Printed Printed Dipole Antenna for Indoor Small Cell Base station in LTE System,” 2017 2nd International Conferences on Information Technology, Information System and Electrical Engineering (ICITISEE), 2017, pp. 207-210.

I.D.K. Putra, P.R. Widhi, and A.G.F. Ifur, 4G LTE Advanced for Beginner and Consultant Handbook, Jakarta, Indonesia: Prandia Self Publishing, 2017.

A.A. Pratiwi and Nadhifah, "Rancang Bangun Antena Lungs Microstrip Array untuk Aplikasi GPS dan LTE ", Thesis, Hasanuddin University, Makassar, Indonesia, 2010.

S. Tripambudi, (2014) "Impedansi Antena", [Online], https://prezi.com/ed78u5mxsrg0/impedansi-antenna/, accessed: 8-Sep-2018.

W.L. Stutzman and G.A. Thielle, Antenna Theory and Design, Virginia, USA: Wiley and Sons, Inc., 2012.

R. Zingg, “Printed Dipole Antenna,” Magister Thesis, University of Colorado at Boulder, Colorado, USA, 2011.

B. Setiyanto, Dasar Dasar Telekomunikasi, Yogyakarta, Indonesia: Sakti, 2010.

C.A. Balanis, Antenna Theory Analysis and Design Third Edition, New Jersey, USA: John Wiley & Sons, Inc., 2005.

(2017) “Antennas and Propagation: SMA Connector” [Online], http://www.radioelectronics.com/info/antennas/coax/sma_connector.php, access date: 8-Sep-2017.

W.D. Reeve, "The SMA RF Connector and Associated Tools," in Manual Books for Antenna Engineering, Reeve Engingeers, 2004.

(2018) “FR-4” [Online], https://www.microwaves101.com/ encyclopedias/fr-4, access date: 8-Sep-18.

I.G.N. Dharmayana, I.P. Ardana, and I.M.O. Widyantara, "Rancang Bangun Antena Yagi pada Frekuensi 1800 Mhz Untuk Penguat Sinyal Modem ", Master Thesis, Udayana University, Bali, Indonesia, 2016.

“User’s Guide – High Frequency Structure Simulator,” Ansoft Corporation, Pittsburgh, USA, 2005, pp. 62-71.

Paul, (2017) “MiniVNA Tiny Plus Review,” [Online], https://www.disk91.com/2017/technology/hardware/Minivna-tiny-plus -review/, access date: 8-Sep-18.

C.Y. Chu, “Printed Dipole Antenna Design for Wireless Communications,” Thesis, McGill University, Montreal, Canada, Juli 2015.

J. Nourinia, P. Rezaei, A. Valizade, and B. Mohammadi, “Design of an Omnidirectional Triple Band Bent-Fork Shaped Microstrip Monopole Antenna for Multiband Applications,” 2015 23rd Iranian Conference on Electrical Engineering (ICEE), 2015, pp. 546-549.

J.M. Floc’h, Y. Kokar, J.M. Denoual,” Design of Dual Band Printed Dipole with Compensation of Frequency Space Attenuation,” 2010 Loughborough Antennas & Propagation Conference, 2010, pp. 117-120.

(2017) “What is VSWR and Return loss” [Online], http://www.techplayon.com/vswr-return-loss/, access date: 8-Sep-18.

(2018) “Dipole Radiation Pattern: Polar Diagram” [Online], https://www.radio-electronics.com/info/antennas/dipole/radiation-patterns.php, access date: 8-Sep-18.



DOI: https://doi.org/10.22146/ijitee.43842

Article Metrics

Abstract views : 208 | views : 48

Refbacks

  • There are currently no refbacks.




Copyright (c) 2019 IJITEE (International Journal of Information Technology and Electrical Engineering)

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

ISSN  : 2550-0554 (online)

Contact :

Department of Electrical engineering and Information Technology, Faculty of Engineering
Universitas Gadjah Mada

Jl. Grafika No 2 Kampus UGM Yogyakarta

+62 (274) 552305

Email : ijitee.ft@ugm.ac.id

----------------------------------------------------------------------------