Treatment of Wastewater Containing Wood Waste Pyroligneous Acid Preservative by Activated Carbon in Rubberwood Manufacturing Process

https://doi.org/10.22146/ajche.50100

Rizafizah Othaman(1), Agus Susilo(2), Hiroaki Habaki(3), Ryuichi Egashira(4*)

(1) School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia
(2) School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia
(3) School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia
(4) School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia
(*) Corresponding Author

Abstract


In this paper, the feasibility of using the products from thermal treatment of rubberwood waste, i.e., pyroligneous acid as preservative and activated carbon as adsorbent to treat the wastewater containing the preservative was studied. Firstly, the sawdust was thermally treated under various conditions to produce the pyroligneous acid and the activated carbon. Atmosphere and treatment temperature were a significant factor in determining the yield of the products. Secondly, the equilibrium adsorption runs were carried out with the model wastewater containing single, multi solutes, or the pyroligneous acid and with the activated carbon obtained under steam atmosphere. Phenolic compounds were adsorbed at the highest in single solute solutions, and lower in multi solutes solutions. Finally, the feasibility of this process improvement was discussed.

Keywords


adsorption; environmental problems; phenolic compounds; process improvement; thermal treatment; wastewater treatment

Full Text:

PDF


References

  1. Faghemi, L., Khezami L. and Capart R. (2001). Pyrolysis Products from Different Biomasses: Application to the Thermal Cracking of Tar, Appl. Energy, 69, 293.
  2. Jain, S.J., and Snoeyink, V. L. (1973). Adsorption from Bisolute Systems on Active Carbon, J. of Water Pollution Control Fed. , 45, 2463.
  3. Lim, K.G., and Egashira, R. (2004, April 2). Characterization of Products from Thermal Treatment of Rubberwood (In Japanese), Osaka, Japan. SCEJ 69th Meeting, Osaka University, Osaka City, Japan.
  4. Ministry of Science, Technology and the Environment. (1999). 1999 Annual Report, Ministry of Science, Technology and the Environment, Kuala Lumpur, Malaysia.
  5. Othaman, R., Lim, K.G., Konishi, S., Sato, M., Shi, N., and Egashira, R. (2008). Thermal Treatment of Wood Residues and Effective Utilization of Its Products to Improve Rubberwood Manufacturing Process, J. of Chem. Engng. of Japan, 41(12),1149.
  6. Othaman, R., Lim, K.G., Konishi, S., Sato, M., Shanshan, Q., Shi, N., and Egashira, R. (2007, May 15). Thermal Treatment of Rubberwood Residue for Its Effectual Use, Phoenix, USA. 26th Annual International Conference on Incineration and Thermal Treatment Technologies (IT3) Meeting, The Sheraton Crescent Hotel, Arizona, USA.
  7. Othaman, R., K.G. Lim, S. Konishi, R.Egashira and H. Habaki. (2008, October 17). Utilization of Thermal Treatment Products from Wood Residues to Improve Rubberwood Manufacturing Process, Tokyo, Japan. International Workshop on Process Intensification 2008, Tokyo Institute of Technology, Tokyo, Japan.
  8. Yoshida, H. (2005). Handbook on Porous Adsorbent. Fuji Technosystem, Tokyo, Japan.



DOI: https://doi.org/10.22146/ajche.50100

Article Metrics

Abstract views : 1437 | views : 795

Refbacks

  • There are currently no refbacks.


ASEAN Journal of Chemical Engineering  (print ISSN 1655-4418; online ISSN 2655-5409) is published by Chemical Engineering Department, Faculty of Engineering, Universitas Gadjah Mada.